MARUTI SUZUKI BALENO 2017 Owner'S Manual Download Page 187

Page: 187 / 324

5-15

OTHER CONTROLS AND EQUIPMENT

68PH0-74E

Frame Hooks

Front

68PM05005

The towing hook (1) is provided on the

front of the vehicle for use in emergency

situations only.
To install the hook (1), follow the procedure

below.

61MM0B039

1) Pick up the towing hook (1), jack handle

(A) and wheel brace (B) that are stowed

in the luggage compartment.

68PM05006

2) Remove the cover (C) by using a jack

handle (A) covered with a soft cloth as

shown in the illustration.

68PM05007

3) Install the towing hook (1) by hand.

(1)

EXAMPLE

(1)

(A)

(B)

EXAMPLE

(A)

(C)

EXAMPLE

(1)

EXAMPLE

Summary of Contents for BALENO 2017





































































































































































































































































































































Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands

MARUTI SUZUKI BALENO 2017, Owner'S Manual

Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands