MARUTI SUZUKI BALENO 2017 Owner'S Manual Download Page 106

Page: 106 / 324

2-88

BEFORE DRIVING

68PH0-74E

Warning and indicator

message

Master warning

indicator light

Sound

Cause and remedy

68PH02239

Blinks

Beep (One time from interior

buzzer)

There is a problem with the steering lock

system.

Have your vehicle inspected by an autho-

rized Maruti Suzuki workshop.

68PH02240

Blinks

Beep (One time from interior

buzzer)

There is a problem with the keyless push

start system. Also, the vehicle battery volt-

age may be decreased.

When the message is displayed even if you

start the engine with normal voltage of the

vehicle battery, have your vehicle inspected

by an authorised Maruti Suzuki workshop.

Summary of Contents for BALENO 2017





































































































































































































































































































































Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands

MARUTI SUZUKI BALENO 2017, Owner'S Manual

Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands