MARUTI SUZUKI BALENO 2017 Owner'S Manual Download Page 242

Page: 242 / 324

5-70

OTHER CONTROLS AND EQUIPMENT

68PH0-74E

Battery Installation

Install a lithium battery (CR2025) with the poles facing the correct direction.

68PM5001

Battery replacement timing

• When battery power is depleted, the button may not be operable. If the remote controller

does not operate, replace the battery and check the operation.

Caution on battery

• Be sure to follow the instructions to prevent battery leakage, over-heating, ignition or

explosion.

EXAMPLE

If battery leakage has occurred, wipe the

container first then install a new battery. If

the battery solution contacts the skin, wash

off with water completely.

WARNING

• Do not expose the battery to flame.

Do not short circuit, disassemble,

or heat the battery.

• Do not charge the battery.

• Use the specified type battery.

• Keep the button-shaped battery

away from children to prevent acci-

dental swallowing.

If the battery is swallowed, contact a

doctor immediately.

CAUTION

• Install the battery with the poles

facing the correct direction.

• When not in use for a long period

of time, or if the battery is dead,

remove the battery from the remote

controller.

Summary of Contents for BALENO 2017





































































































































































































































































































































Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands

MARUTI SUZUKI BALENO 2017, Owner'S Manual

Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands