MARUTI SUZUKI BALENO 2017 Owner'S Manual Download Page 244

Page: 244 / 324

5-72

OTHER CONTROLS AND EQUIPMENT

68PH0-74E

Remote Controller

Common operations

In Sound Mode

Press to adjust the sound.(bass/treble/balance/fader)

In Preset-EQ Mode

The Preset-EQ setting switches as follows:

In AVC Mode

The AVC setting switches

as follows:

TUNE FOLDER UP/DOWN button

OFF (FLAT)

JAZZ

ROCK

POP

CLASSIC

HIP-HOP

OFF

LEVEL 1

LEVEL 2

LEVEL 3

Power ON / OFF

POWER button

Press to adjust volume.

(including at AUX mode)

VOLUME button

Press to mute the sound. Press it again to cancel

the mute.

MUTE button

While playback, the sound

mode switches as follows

(including at AUX mode,

except while displaying

iPod

menu):

SOUND button

Preset-EQ

BASS

TREBLE

BALANCE

FADER

AVC

The mode switches as

follows:

MODE button

FM1

FM2

Bluetooth

audio

(If equipped)

AUX (If equipped)

USB (iPod

)

(If equipped)

Summary of Contents for BALENO 2017





































































































































































































































































































































Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands

MARUTI SUZUKI BALENO 2017, Owner'S Manual

Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands