MARUTI SUZUKI BALENO 2017 Owner'S Manual Download Page 289

Page: 289 / 324

7-33

INSPECTION AND MAINTENANCE

68PH0-74E

Front Fog Light (If equipped)

1) Start the engine. Turn the steering

wheel to the opposite side of the replac-

ing fog light to replace the bulb easily.

Then turn off the engine.

68PM07002

2) Remove the clips (1).

68PM07003

3) Open the end of the cover inside the

fender.

68PH00736

4) Disconnect the coupler by pushing the

lock release. Turn the bulb holder coun-

terclockwise and remove it.

Rear combination light

68PH00737

1) Remove the bolts (1) and pull the light

housing (2) straight.

68PH00738

2) Remove the wire (3) from a clamp (4).

(1)

EXAMPLE

(1)

(2)

EXAMPLE

(4)

(3)

EXAMPLE

Summary of Contents for BALENO 2017





































































































































































































































































































































Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands

MARUTI SUZUKI BALENO 2017, Owner'S Manual

Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands