MARUTI SUZUKI BALENO 2017 Owner'S Manual Download Page 89

Page: 89 / 324

2-71

BEFORE DRIVING

68PH0-74E

68PM00272

NOTE:

• As shown in the above illustration, “SEL”

indicates on the display of currently set-

ting item.

• To go back to the higher level display

during operation, turn the indicator

selector knob (3) to display “

” or

“

” and then push the indicator

selector knob (3).

• If the security system “

” is in the dis-

abled state, the shock sensor “

”, pre-

warning sensitivity “

” and full blast

warning sensitivity “

” cannot be set

up.

4) to exit the setting mode, switch the dis-

play to show “

” and then push the

indicator selector knob (3).

EXAMPLE

Summary of Contents for BALENO 2017





































































































































































































































































































































Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands

MARUTI SUZUKI BALENO 2017, Owner'S Manual

Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands