MARUTI SUZUKI BALENO 2017 Owner'S Manual Download Page 128

Page: 128 / 324

2-110

BEFORE DRIVING

68PH0-74E

Horn

68PH00265

Press the horn button of the steering wheel

to sound the horn. The horn will sound with

the ignition switch in any position or any

ignition mode.

Heated Rear Window Switch
(If equipped)

68PH00266

When the rear window is misted, push this

switch (1) to clear the window.
An indicator light will be lit when the defog-

ger is on. The defogger will work only

when the engine is running. To turn off the

defogger, push the switch again.

WARNING

Never attempt to adjust the steering

wheel while the vehicle is moving or

you could lose control of the vehicle.

EXAMPLE

NOTICE

The heated rear window uses a large

amount of electricity. Be sure to turn

off after the window has become

clear.

(1)

EXAMPLE

Summary of Contents for BALENO 2017





































































































































































































































































































































Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands

MARUTI SUZUKI BALENO 2017, Owner'S Manual

Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands