MARUTI SUZUKI BALENO 2017 Owner'S Manual Download Page 50

Page: 50 / 324

2-32

BEFORE DRIVING

68PH0-74E

80J2008

NOTE:

The word “CENTER” is marked on the

buckle for the rear center belt. The buckles

are designed so a latch plate cannot be

inserted into the wrong buckle.

60A039

To unfasten the seat belt, push the red

“PRESS” button on the buckle and retract

the belt slowly while attaching a hand to

the belt or/and the latch plate.

Lap Belt

Rear Center Seat Belt

To fasten the belt, pull the latch plate

attached to the seat belt across your hips

and press it straight into the buckle until

you hear a “click”. To reduce the risk of

sliding under the belt during a collision,

position the belt across your lap as low on

your hips as possible and adjust it to a

snug fit.

80JS028

To tighten the belt, pull the free end of the

belt across alongside the lap strap.

EXAMPLE

TO TIGHTEN

Low on hips

EXAMPLE

Summary of Contents for BALENO 2017





































































































































































































































































































































Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands

MARUTI SUZUKI BALENO 2017, Owner'S Manual

Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands