MARUTI SUZUKI BALENO 2017 Owner'S Manual Download Page 135

Page: 135 / 324

3-5

OPERATING YOUR VEHICLE

68PH0-74E

Engine Switch
(Vehicle with keyless push
start system)

68PH00302

LOCK (OFF)

This mode is for parking the vehicle. When

this mode is selected by pressing the

engine switch and then any door (Including

the tailgate) is opened or closed, the steer-

ing will be locked automatically.

ACC

Press the engine switch to select this igni-

tion mode to use such electric equipment

as the audio system, outside rearview mir-

rors and accessory socket with the engine

off. When this position is selected, the

information display in the instrument clus-

ter shows the following message: “ACC”

IGNITION SWITCH POSITION. Refer to

“Information Display” in the “BEFORE

DRIVING” section for details.

• With the engine off

You can use such electric equipment as

the power windows and wipers with the

engine off. When this ignition mode is

selected by pressing the engine switch,

the information display in the instrument

cluster shows the following message:

“ON” IGNITION SWITCH POSITION.

• With the engine on

All electric equipment is operational. The

vehicle can be driven when you have

selected this ignition mode by pressing

the engine switch.

START

Provided you have the keyless push start

system remote controller with you, the

engine automatically starts when you

press the engine switch to select this igni-

tion mode after shifting to “N” (Neutral) and

depressing the brake and clutch pedals.

NOTE:

You do not need to keep the engine switch

pressed to start the engine.

NOTE:

In the presence of strong radio signals or

noise, you may not be able to change the

ignition mode to “ACC” or “ON” or to start

the engine using the engine switch. In this

case, the information display on the instru-

ment cluster will show the following mes-

sage: KEY FOB NOT DETECTED.

Unreleased Steering Lock Warning

If the steering lock remains engaged when

you press the engine switch to change the

ignition mode to “ON”, the information dis-

play in the instrument cluster shows the

message: “TRN. STEERING WHEEL TO

RELEASE LOCK”. Refer to “Information

Display” in the “BEFORE DRIVING” sec-

tion for details.

NOTE:

The steering lock may not be released if

some load is acting on the steering wheel.

If this happens, turn the steering wheel to

the right or left to relieve it from the load

before you press the engine switch again

to change to the desired ignition mode.

EXAMPLE

NOTICE

Do not leave the engine switch in the

“ACC” or “ON” mode when the

engine is not running. Avoid using

the radio or other electric accesso-

ries for a long time when the engine

switch is in the “ACC” or “ON” mode

when the engine is not running, oth-

erwise the battery may discharge.

Summary of Contents for BALENO 2017





































































































































































































































































































































Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands

MARUTI SUZUKI BALENO 2017, Owner'S Manual

Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands