MARUTI SUZUKI BALENO 2017 Owner'S Manual Download Page 167

Page: 167 / 324

4-5

DRIVING TIPS

68PH0-74E

If Your Vehicle Gets Stuck

If your vehicle gets stuck in snow, mud, or

sand, follow the directions below:
1) Shift the transaxle back and forth

between a forward range (or first gear

for manual transaxle) and reverse. This

will create a rocking motion which may

give you enough momentum to free the

vehicle. Press gently on the accelerator

to keep wheel spinning to a minimum

wheel rpm. Remove your foot from the

accelerator while shifting.

Do not race the engine. Excessive

wheel spin will cause the tires to dig

deeper, making it more difficult to free

the vehicle.

2) If your vehicle remains stuck after a few

minutes of rocking, we recommend you

to consult your authorised Maruti

Suzuki workshop or a roadside assis-

tance service. If a towing service is not

available in an emergency, your vehicle

may be temporarily towed by a towing

cable or chain secured to the towing

hook either on the front of the vehicle or

on the rear of the vehicle. Refer to

“Frame Hooks” in the “OTHER CON-

TROLS AND EQUIPMENT” section.

Driving on Wet Roads

WARNING

Do not allow anyone to stand near

the vehicle when you are rocking it,

and do not spin the wheels faster

than an indicated 40 km/h on the

speedometer. Personal injury and/or

vehicle damage may result from spin-

ning the wheels too fast.

NOTICE

Do not continue rocking the vehicle

for more than a few minutes. Pro-

longed rocking can cause engine

overheating or transaxle damage.

NOTICE

• When driving on wet roads, avoid

driving through large amount of

standing water on the road. Large

amount of water entering the

engine compartment may cause

damage to the engine and or elec-

trical components.

• If stuck in deep water, do not start

the engine.

• Water is incompressible substance,

water inside engine is harmful to

the engine.

WARNING

In addition to following the driving

tips in this section, it is important to

observe the following precautions.

• Make sure your tires are in good

condition and always maintain the

specified tire pressure. Refer to

“Tires” in the “INSPECTION AND

MAINTENANCE” section for

details.

(Continued)

Summary of Contents for BALENO 2017





































































































































































































































































































































Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands

MARUTI SUZUKI BALENO 2017, Owner'S Manual

Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands