MARUTI SUZUKI BALENO 2017 Owner'S Manual Download Page 111

Page: 111 / 324

2-93

BEFORE DRIVING

68PH0-74E

• If your vehicle is equipped with a parking sensor system, the information display also indicates warning and indicator messages

related to the system. For information on these messages, refer to “Parking sensors (If equipped)” in “OPERATING YOUR VEHICLE”

section.

Warning and indicator

message

Master warning

indicator light

Sound

Cause and remedy

68PH02249

Off

If the coolant temperature is cool enough,

this message is displayed when the engine

switch is pressed to change the ignition

mode to “ON” and this message will disap-

pear when the glow plug is heated enough

for engine starting.

Summary of Contents for BALENO 2017





































































































































































































































































































































Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands

MARUTI SUZUKI BALENO 2017, Owner'S Manual

Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands