manualshive.com logo in svg

MARUTI SUZUKI BALENO 2017, Owner'S Manual

The MARUTI SUZUKI BALENO 2017 Owner's Manual is a comprehensive guide that provides users with essential information about their vehicle. This manual can be easily downloaded for free from manualshive.com, allowing owners to access this important resource at their convenience.

Share
Download
background image

7-14

INSPECTION AND MAINTENANCE

68PH0-74E

K12M model

68PM00706

1) Unclamp the side clamps and remove

the element from the air cleaner case.If

the element appears to be dirty clean

the element or replace it with a new one

as per periodic maintenance schedule.

2) Clamp the side clamps securely.

(For diesel engine model)

68PH00711

1) Loosen the screws and remove the ele-

ment from the air cleaner case. If the

element appears to be dirty clean the

element or replace it with a new one as

per periodic maintenance schedule.

2) Tighten the screws securely.

Spark Plugs (Petrol engine)

Replacing and inspection of spark 

plugs

Since special procedures, materials and

tools are required, it is recommended that

you trust this job to your authorised Maruti

Suzuki workshop.

EXAMPLE

EXAMPLE

Summary of Contents for BALENO 2017





































































































































































































































































































































Reviews:

No comments

Related manuals for BALENO 2017

AA Products KX405 Instruction Manual preview
KX405
Brand: AA Products Pages: 8
Jeep Automobile Service And Warranty Handbook preview
Automobile
Brand: Jeep Pages: 42
Jeep Automobile Warranty Information Booklet preview
Automobile
Brand: Jeep Pages: 44
Cadillac ATS 2015 Convenience/Personalization Manual preview
ATS 2015
Brand: Cadillac Pages: 20
Jeep Automobile Service Contract preview
Automobile
Brand: Jeep Pages: 7
Cadillac 2016 ELR Convenience/Personalization Manual preview
2016 ELR
Brand: Cadillac Pages: 20
Cadillac 2016 CTS Manual preview
2016 CTS
Brand: Cadillac Pages: 354
Cadillac 2005 CTS Personalization Manual preview
2005 CTS
Brand: Cadillac Pages: 20
Cadillac 2014 XTS Convenience/Personalization Manual preview
2014 XTS
Brand: Cadillac Pages: 20
Cadillac ATS 2014 Specifications preview
ATS 2014
Brand: Cadillac Pages: 10
Cadillac 2013 Escalade ESV Owner'S Manual preview
2013 Escalade ESV
Brand: Cadillac Pages: 524
Cadillac 2013 ATS Personalization Manual preview
2013 ATS
Brand: Cadillac Pages: 20
Cadillac ATS 2013 Owenrs Manual preview
ATS 2013
Brand: Cadillac Pages: 438
Cadillac 2013 ATS Owner'S Manual preview
2013 ATS
Brand: Cadillac Pages: 450
Cadillac 2011 Escalade Hybrid Owner'S Manual Addendum preview
2011 Escalade Hybrid
Brand: Cadillac Pages: 94
Cadillac 2011 Escalade Hybrid Owner'S Manual preview
2011 Escalade Hybrid
Brand: Cadillac Pages: 94
Cadillac 2011 CTS COUPE Navigation Manual preview
2011 CTS COUPE
Brand: Cadillac Pages: 78
Cadillac 2011 CTS COUPE Brochure preview
2011 CTS COUPE
Brand: Cadillac Pages: 8

Brands by name

Popular brands

Load more brands