MARUTI SUZUKI BALENO 2017 Owner'S Manual Download Page 91

Page: 91 / 324

2-73

BEFORE DRIVING

68PH0-74E

Speedometer

The speedometer indicates vehicle speed.

Tachometer

The tachometer indicates engine speed in

revolutions per minute.

Fuel Gauge

68PH02223

When the ignition mode is “ON”, this

gauge gives an approximate indication of

the amount of fuel in the fuel tank. “F”

stands for full and “E” stands for empty.
If the indicator approaches a low level

(Near “E”) on fuel gauge, refill the tank as

soon as possible.

NOTE:

The indicator moves a little depending on

road conditions (For example, slope or

curve) and driving conditions because of

fuel moving in the tank.

If the low fuel warning light (1) comes on,

fill the fuel tank immediately.

Refer to “Low fuel warning light” in “Warn-

ing and indicator lights” in this section for

details.
The mark (2) indicates that the fuel filler

door is located on the left side of the vehi-

cle.

NOTICE

Never drive the vehicle with the

engine revving in the red zone or

severe engine damage can result.

Keep the engine speed below the red

zone even when downshifting to a

lower gear position.

Refer to “Downshifting maximum

allowable speeds” in “OPERATING

YOUR VEHICLE” section.

(1)

(2)

(1)

(2)

EXAMPLE

Summary of Contents for BALENO 2017





































































































































































































































































































































Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands

MARUTI SUZUKI BALENO 2017, Owner'S Manual

Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands