MARUTI SUZUKI BALENO 2017 Owner'S Manual Download Page 186

Page: 186 / 324

5-14

OTHER CONTROLS AND EQUIPMENT

68PH0-74E

Luggage Compartment Hook
(If equipped)

68PH00531

You can hang the shopping bag or other

suitable objects on the hook.

This hook is not designed for large or

heavy items.

Luggage Compartment Cover

68PH00532

Luggage or other cargo placed in the lug-

gage compartment is hidden from view by

a luggage compartment cover.

WARNING

Failure to take the following precau-

tions may result in the driver’s side

floor mat interfering with the pedals

and causing a loss of vehicle control

or an accident.

• Make sure that the floor mat grom-

mets are hooked to the fasteners.

• Never place additional floor mats

on top of the existing floor mat.

NOTICE

To avoid breaking the hook, do not

hang items heavier than following

weight.

Shopping hook: 2 kg (4.4 lbs)

EXAMPLE

WARNING

Do not carry items on top of the lug-

gage compartment cover, even if they

are small and light. Objects on top of

the cover could be thrown about in

an accident, causing injury, or could

obstruct the driver’s rear view.

EXAMPLE

Summary of Contents for BALENO 2017





































































































































































































































































































































Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands

MARUTI SUZUKI BALENO 2017, Owner'S Manual

Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands