MARUTI SUZUKI BALENO 2017 Owner'S Manual Download Page 82

Page: 82 / 324

2-64

BEFORE DRIVING

68PH0-74E

Information Display

The information display is shown when the

ignition switch is in the “ON” position.

68PH02212

(1) Information display

68PH02213

(2) Trip meter selector knob

(3) Indicator selector knob

The information display shows the follow-

ing information.

Display (A)

Thermometer

Display (B)

Selector position (for CVT

vehicles) / Gearshift indicator (for manual

transaxle vehicles)

Display (C)

Trip meter / Odometer / Instantaneous fuel

consumption / Average fuel consumption /

Driving range

Display (D)

Clock

Thermometer

When the ignition switch is in the “ON”

position, the display (A) shows the ther-

mometer.

The thermometer indicates the outside

temperature.

68PH02214

If the outside temperature nears freezing,

the mark (a) will appear on the display.

NOTE:

• The outside temperature indication is not

the actual outside temperature when

driving at low speed, or when stopped.

• If there is something wrong with the ther-

mometer, or just after the ignition switch

is turned to the “ON” position, the display

may not indicate the outside tempera-

ture.

(1)

(A)

(B)

(C)

(D)

EXAMPLE

(3)

(2)

EXAMPLE

(a)

EXAMPLE

Summary of Contents for BALENO 2017





































































































































































































































































































































Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands

MARUTI SUZUKI BALENO 2017, Owner'S Manual

Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands