MARUTI SUZUKI BALENO 2017 Owner'S Manual Download Page 118

Page: 118 / 324

2-100

BEFORE DRIVING

68PH0-74E

Glow Plug Indicator Light

(If equipped)

60A543

If the coolant temperature is cool enough,

this light comes on when the ignition

switch is turned to the “ON” position or the

engine switch is pressed to change the

ignition mode to “ON” and goes out when

the glow plug is heated enough for engine

starting.

Fuel Filter Warning Light

(If equipped)

60A541

This light comes on for several seconds

when the ignition switch is turned to the

“ON” position or the engine switch is

pressed to change the ignition mode to

“ON” so you can check that light is work-

ing.

If the light comes on when driving, there is

a possibility to have water in the fuel filter.

Drain water as soon as possible. Have

your vehicle inspected by an authorised

Maruti Suzuki workshop.

Master Warning Indicator Light

(If equipped)

78K049

When the information display shows warn-

ing and indicator messages, this indicator

light may also blink.
For details, refer to “Information display” in

this section.

Lighting Control Lever

65D611

WARNING

To avoid possible injury, do not oper-

ate controls by reaching through the

steering wheel.

EXAMPLE

Summary of Contents for BALENO 2017





































































































































































































































































































































Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands

MARUTI SUZUKI BALENO 2017, Owner'S Manual

Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands