MARUTI SUZUKI BALENO 2017 Owner'S Manual Download Page 206

Page: 206 / 324

5-34

OTHER CONTROLS AND EQUIPMENT

68PH0-74E

The Bluetooth

word mark and logo are

registered trademarks and are owned by

the Bluetooth SIG, Ink.

Stop using this unit and a Bluetooth

ready device whenever requested.

This unit shares the communication fre-

quency with other private or public wireless

communication equipment such as a wire-

less LAN and other wireless communica-

tion radios.

You should stop using this unit whenever

you are notified that your unit disturbs

other wireless communication immediately.

WARNING

This is a class I laser product. Use of

controls or adjustments or perfor-

mance of procedures other than

those specified herein may result in

hazardous radiation exposure.

Do not open covers and do not

attempt to repair this unit by yourself.

Refer servicing to qualified person-

nel.

Summary of Contents for BALENO 2017





































































































































































































































































































































Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands

MARUTI SUZUKI BALENO 2017, Owner'S Manual

Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands