MARUTI SUZUKI BALENO 2017 Owner'S Manual Download Page 280

Page: 280 / 324

7-24

INSPECTION AND MAINTENANCE

68PH0-74E

Battery

54GM701

For maintenance-free battery (Cap-less

type), you need not add water. For tradi-

tional type battery, which has water filler

caps, the level of the battery solution must

be kept between the “MAX” and the “MIN”

level lines at all times. If the level is found

to be below the “MIN” level line, add dis-

tilled water to the “MAX” level line. You

should periodically check the battery, bat-

tery terminals, and battery hold-down

bracket for corrosion. Remove corrosion

using a stiff brush and ammonia mixed

with water, or baking soda mixed with

water. After removing corrosion, rinse with

clean water.
If your vehicle is not going to be driven for

a month or longer, disconnect the cable

from the negative terminal of the battery to

help prevent discharge.

Replacement of the battery

For petrol engine model

68PH00719

For diesel engine model

68PH00720

WARNING

• Batteries produce flammable

hydrogen gas. Keep flames and

sparks away from the battery or an

explosion may occur. Never smoke

when working in the vicinity of the

battery.

• When checking or servicing the

battery, disconnect the negative

cable. Be careful not to cause a

short circuit by allowing metal

objects to contact the battery posts

and the vehicle at the same time.

• To avoid harm to yourself or dam-

age to your vehicle or battery, fol-

low the jump starting instructions

in the “EMERGENCY SERVICE”

section of this manual if it is neces-

sary to jump start your vehicle.

• Diluted sulfuric acid spilled from

battery can cause blindness or

severe burns. Use proper eye pro-

tection and gloves. Flush eyes or

body with ample water and get

medical care immediately if suf-

fered. Keep batteries out of the

reach of children.

MAX

MIN

EXAMPLE

(1)

(2)

(3)

(4)

EXAMPLE

(1)

(2)

(3)

(4)

EXAMPLE

Summary of Contents for BALENO 2017





































































































































































































































































































































Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands

MARUTI SUZUKI BALENO 2017, Owner'S Manual

Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands