MARUTI SUZUKI BALENO 2017 Owner'S Manual Download Page 108

Page: 108 / 324

2-90

BEFORE DRIVING

68PH0-74E

(#1) This message will disappear for a while even if the problem that caused the message to appear is not corrected.

Warning and indicator

message

Master warning

indicator light

Sound

Cause and remedy

68PH02243

Off

This message is displayed when “ON” posi-

tion is selected as the power supply posi-

tion. (#1)

68PH02244

Blinks

Beep (One time from interior

buzzer)

The steering lock is not disengaged. While

lightly turning the steering wheel in both

directions, press the engine switch again.

Summary of Contents for BALENO 2017





































































































































































































































































































































Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands

MARUTI SUZUKI BALENO 2017, Owner'S Manual

Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands