MARUTI SUZUKI BALENO 2017 Owner'S Manual Download Page 306

Page: 306 / 324

8-8

EMERGENCY SERVICE

68PH0-74E

If the Engine Overheats

The engine could overheat temporarily

under severe driving conditions. If the

engine coolant temperature gauge indi-

cates overheating during driving:
1) Turn off the air conditioner, if equipped.

2) Take the vehicle to a safe place and

park.

3) Let the engine run at the normal idle

speed for a few minutes until the indica-

tor is within the normal, acceptable tem-

perature range between “H” and “C”.

If the temperature indication does not

come down to within the normal, accept-

able range:
1) Turn off the engine and check that the

water pump belt and pulleys are not

damaged or slipping. If any abnormality

is found, correct it.

2) Check the coolant level in the reservoir.

If it is found to be lower than the “LOW”

line, look for leaks at the radiator, water

pump, and radiator and heater hoses. If

you locate any leaks that may have

caused the overheating, do not run the

engine until these problems have been

corrected.

3) If you do not find a leak, carefully add

coolant to the reservoir and then the

radiator, if necessary. (Refer to “Engine

Coolant” in the “INSPECTION AND

MAINTENANCE” section.)

NOTE:

If your engine overheats and you are

unsure what to do, contact your authorised

Maruti Suzuki workshop.

79J007

65D350d

WARNING

If you see or hear escaping steam,

stop the vehicle in a safe place and

immediately turn off the engine to let

it cool. Do not open the hood when

steam is present. When the steam

can no longer be seen or heard, open

the hood to see if the coolant is still

boiling. If it is, you must wait until it

stops boiling before you proceed.

EXAMPLE

Summary of Contents for BALENO 2017





































































































































































































































































































































Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands

MARUTI SUZUKI BALENO 2017, Owner'S Manual

Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands