MARUTI SUZUKI BALENO 2017 Owner'S Manual Download Page 80

Page: 80 / 324

2-62

BEFORE DRIVING

68PH0-74E

Speedometer

The speedometer indicates vehicle speed.

Tachometer

The tachometer indicates engine speed in

revolutions per minute.

Fuel Gauge

68PH02209

When the ignition switch is in the “ON”

position, this gauge gives an approximate

indication of the amount of fuel in the fuel

tank. “F” stands for full and “E” stands for

empty.
If the indicator gets off the graduation of

“E” (Not character “E”), refill the tank as

soon as possible.

NOTE:

The indicator moves a little depending on

road conditions (For example, slope or

curve) and driving conditions because of

fuel moving in the tank.

If the low fuel warning light (1) comes on,

fill the fuel tank immediately.

Refer to “Low Fuel Warning Light” in

“Warning and Indicator Lights” in this sec-

tion for details.
The mark (2) indicates that the fuel filler

door is located on the left side of the vehi-

cle.

NOTICE

Never drive the vehicle with the

engine revving in the red zone or

severe engine damage can result.

Keep the engine speed below the red

zone even when downshifting to a

lower gear position.

Refer to “Downshifting maximum

allowable speeds” in the “OPERAT-

ING YOUR VEHICLE” section.

(1)

(2)

(1)

(2)

EXAMPLE

Summary of Contents for BALENO 2017





































































































































































































































































































































Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands

MARUTI SUZUKI BALENO 2017, Owner'S Manual

Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands