MARUTI SUZUKI BALENO 2017 Owner'S Manual Download Page 195

Page: 195 / 324

5-23

OTHER CONTROLS AND EQUIPMENT

68PH0-74E

Maintenance

If you do not use the air conditioner for a

long period, such as during winter, it may

not give the best performance when you

start using it again. To help maintain opti-

mum performance and durability of your air

conditioner, it needs to be run periodically.

Operate the air conditioner at least once a

month for one minute with the engine

idling. This circulates the refrigerant and oil

and helps protect the internal components.
If your air conditioner is equipped with air

filters, clean or replace them as specified

in the “Maintenance Schedule” in the

“INSPECTION AND MAINTENANCE” sec-

tion.

NOTE:

Your vehicle uses the air conditioning

refrigerant HFC-134a, commonly called

“R-134a”. R-134a replaced R-12 around

1993 for automotive applications. Other

refrigerants are available, including recy-

cled R-12, but only R-134a should be used

in your vehicle.

NOTICE

Using the wrong refrigerant may

damage your air conditioning sys-

tem. Use R-134a only. Do not mix or

replace the R-134a with other refrig-

erants.

Summary of Contents for BALENO 2017





































































































































































































































































































































Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands

MARUTI SUZUKI BALENO 2017, Owner'S Manual

Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands