MARUTI SUZUKI BALENO 2017 Owner'S Manual Download Page 294

Page: 294 / 324

7-38

INSPECTION AND MAINTENANCE

68PH0-74E

60MHM7001

(A) Up

(B) Down

NOTE:

When you install the metal retainers (3),

make sure the direction of metal retainers

as shown in the above illustrations.

5) Install the new blade in the reverse

order of removal, with the locked end

positioned toward the wiper arm.

Make sure the blade is properly

retained by all the hooks. Lock the

blade end into place.

6) Reinstall wiper frame to arm, making

sure that the lock lever is snapped

securely into the arm.

For rear wipers:

68PH00763

1) Hold the wiper arm away from the win-

dow.

2) Remove the wiper frame from the arm

as shown.

3) Slide the blade out as shown.

68PH00764

NOTE:

Do not flex the wiper blade frame end more

than necessary. If you do, it can break off.

(3)

(A)

(B)

(3)

(A)

(B)

EXAMPLE

Summary of Contents for BALENO 2017





































































































































































































































































































































Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands

MARUTI SUZUKI BALENO 2017, Owner'S Manual

Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands