MARUTI SUZUKI BALENO 2017 Owner'S Manual Download Page 183

Page: 183 / 324

5-11

OTHER CONTROLS AND EQUIPMENT

68PH0-74E

Cup Holder and Storage Area

68PM5004

(1) Driver’s pocket

(2) Front cup holders

(3) Front bottle holder

(4) Front armrest with console box

(If equipped)

(5) Rear cup holder (If equipped)

(6) Front seat back pocket (If equipped)

(7) Rear bottle holder

(1)

(2)

(3)

(4)/(5)

(6)

(7)

EXAMPLE

Driver’s Pocket (1)

WARNING

Do not place any objects which may

fall out from the pocket when the

vehicle is moving.

Failure to take the precaution may

result in an object interfering with the

pedals and causing a loss of vehicle

control or an accident.

Summary of Contents for BALENO 2017





































































































































































































































































































































Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands

MARUTI SUZUKI BALENO 2017, Owner'S Manual

Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands