manualshive.com logo in svg

MARUTI SUZUKI BALENO 2017, Owner'S Manual

The MARUTI SUZUKI BALENO 2017 Owner's Manual is a comprehensive guide that provides users with essential information about their vehicle. This manual can be easily downloaded for free from manualshive.com, allowing owners to access this important resource at their convenience.

Share
Download
background image

7-32

INSPECTION AND MAINTENANCE

68PH0-74E

Front turn signal light and 

front position light

Vehicle with the halogen headlights

68PH00730

(1) Front turn signal light

(2) Front position light

Vehicle with the discharge headlights

68PH00731

(1) Front turn signal light

68PH00732

1) Open the engine hood. To remove the

bulb holder of the front turn signal light

or the front position light from the light

housing, turn the holder counterclock-

wise and pull it out.

68PH00733

(3) Removal

(4) Installation

2) To remove the bulb of the front turn sig-

nal light (1) from the bulb holder, push

in the bulb and turn it counterclockwise.

To install a new bulb, push it in and turn

it clockwise.

To remove and install the bulb of the

front position light (2), simply pull out or

push in the bulb.

(1)

(2)

EXAMPLE

(1)

EXAMPLE

EXAMPLE

(1)

(2)

(3)

(4)

EXAMPLE

Summary of Contents for BALENO 2017





































































































































































































































































































































Reviews:

No comments

Related manuals for BALENO 2017

Wagan 2591 User Manual preview
2591
Brand: Wagan Pages: 12
FVC Sprinter Bed System Adventure Wagon Kit Installation Manual preview
Sprinter Bed System Adventure Wagon Kit
Brand: FVC Pages: 8
CITROEN C8 NaviDrive Manual preview
C8 NaviDrive
Brand: CITROEN Pages: 52
BGS technic 40108 Manual preview
40108
Brand: BGS technic Pages: 5
Oldsmobile 1999 88 Owner'S Manual preview
1999 88
Brand: Oldsmobile Pages: 344
ABL eMH3 Installation Manual preview
eMH3
Brand: ABL Pages: 66
Kia Sportage 2018 Features & Functions Manual preview
Sportage 2018
Brand: Kia Pages: 54
Alfa Romeo FIX&GO automatic Manual preview
FIX&GO automatic
Brand: Alfa Romeo Pages: 40
Waeco MagicWatch MWE250 Installation And Operating Manual preview
MagicWatch MWE250
Brand: Waeco Pages: 172
Lexus HS 250h Vehicle Dismantling Manual preview
HS 250h
Brand: Lexus Pages: 34
Toyota 86 2020 Quick Reference Manual preview
86 2020
Brand: Toyota Pages: 32
Aries 2051182 Installation Manual preview
2051182
Brand: Aries Pages: 3
Poison Spyder TrailGate TJ Installation Instructions preview
TrailGate TJ
Brand: Poison Spyder Pages: 5
GMC 2008 Savana Van Owner'S Manual preview
2008 Savana Van
Brand: GMC Pages: 402
MiX Telematics FM 3617i Installation Manual preview
FM 3617i
Brand: MiX Telematics Pages: 39
Carbest 47804 Instruction Manual preview
47804
Brand: Carbest Pages: 64
Honda 08F53-T0A-100 Installation Instructions preview
08F53-T0A-100
Brand: Honda Pages: 2
TracRac TracVan Double Installation Instructions Manual preview
TracVan Double
Brand: TracRac Pages: 6

Brands by name

Popular brands

Load more brands