MARUTI SUZUKI BALENO 2017 Owner'S Manual Download Page 103

Page: 103 / 324

2-85

BEFORE DRIVING

68PH0-74E

Warning and indicator messages
All model

(#1) This message will disappear for a while even if the problem that caused the message to appear is not corrected.

Warning and indicator

message

Master warning

indicator light

Sound

Cause and remedy

68PH02232

Blinks

(Only while vehi-

cle is in motion)

Beep (One time from interior

buzzer; only while vehicle is

in motion)

A door or tailgate is not properly closed.

Stop the vehicle in a safe place and close

the door or tailgate properly. (#1)

68PH02233

Blinks

Continuous beep (From inte-

rior buzzer)

The headlights and/or the position lights are

left on. Turn them off.

Summary of Contents for BALENO 2017





































































































































































































































































































































Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands

MARUTI SUZUKI BALENO 2017, Owner'S Manual

Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands