MARUTI SUZUKI BALENO 2017 Owner'S Manual Download Page 107

Page: 107 / 324

2-89

BEFORE DRIVING

68PH0-74E

Warning and indicator

message

Master warning

indicator light

Sound

Cause and remedy

68PH02241

Blinks

Series of beeps under cer-

tain conditions (For about 2

seconds from exterior and/or

interior buzzers)

The remote controller may be outside the

vehicle or its battery may have become dis-

charged. Locate the remote controller or

touch the engine switch with the remote

controller.

If the message still appears, replace the

remote controller battery.

68PH02242

Summary of Contents for BALENO 2017





































































































































































































































































































































Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands

MARUTI SUZUKI BALENO 2017, Owner'S Manual

Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands