MARUTI SUZUKI BALENO 2017 Owner'S Manual Download Page 250

Page: 250 / 324

5-78

OTHER CONTROLS AND EQUIPMENT

68PH0-74E

Troubleshooting

When encountered a problem, check and follow the instructions as described below.

If the described suggestions do not solve the problem, it is recommended to take the unit to your authorised Maruti Suzuki workshop.

Problem

Possible cause

Possible solution

Common

Unable to operate

The security function is on.

When “SECURITY” is displayed, enter

the ID.

When “HELP” is displayed, contact your

authorised Maruti Suzuki workshop.

Unable to turn on the power (no sound)

(No sound is produced)

Fuse is blown.

Contact your authorised Maruti Suzuki

workshop.

Radio

Much noise

It may not be exactly tuned in to the sta-

tion.

Tune it in exactly to the station.

Unable to receive by auto tuning

There may be no station emitting signals

powerful enough.

Pick up a station by manual tuning.

Sound skips or noise produced

The disc is dirty.

Wipe the disc with a soft cloth.

The disc has a major scratch or is

warped.

Replace the disc with the one with no

scratch and also not warped.

Summary of Contents for BALENO 2017





































































































































































































































































































































Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands

MARUTI SUZUKI BALENO 2017, Owner'S Manual

Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands