LSI LSI53C896 Technical Manual Download Page 239 | Manualshive

Page: 239 / 370

background image

Block Move Instructions

5-11

•

If any other Group Code is received, the

register is not modified and the

LSI53C896 requests the number of bytes specified in
the

DMA Byte Counter (DBC)

register. If the DBC

register contains 0x000000, an illegal instruction
interrupt is generated.

The LSI53C896 transfers the number of bytes specified
in the

DMA Byte Counter (DBC)

register starting at the

address specified in the

DMA Next Address (DNAD)

register. If the Opcode bit is set and a data transfer ends
on an odd byte boundary, the LSI53C896 stores the last
byte in the

SCSI Wide Residue (SWIDE)

register during

a receive operation. This byte is combined with the first
byte from the subsequent transfer so that a wide transfer
can complete.

If the SATN/ signal is asserted by the initiator or a parity
error occurred during the transfer, it is possible to halt the
transfer and generate an interrupt. The Disable Halt on
Parity Error or ATN bit in the

SCSI Control One (SCNTL1)

register controls whether the LSI53C896 halts on these
conditions immediately, or waits until completion of the
current Move.

Initiator Mode

The LSI53C896 verifies that it is connected to the SCSI
bus as an initiator before executing this instruction.

The LSI53C896 waits for an unserviced phase to occur.
An unserviced phase is defined as any phase (with
SREQ/ asserted) for which the LSI53C896 has not yet
transferred data by responding with a SACK/.

The LSI53C896 compares the SCSI phase bits in the

DMA Command (DCMD)

register with the latched SCSI

phase lines stored in the

SCSI Status One (SSTAT1)

register. These phase lines are latched when SREQ/ is
asserted.

OPC

Instruction Defined

0

CHMOV/CHMOV64

1

MOVE/MOVE64

*

«
...
237
238
239
240
241
...
»

Summary of Contents for LSI53C896



















































































































































































































































































































































































Reviews:

No comments

Related manuals for LSI53C896

Brand: K&K Pages: 6

Brand: Mamas & Papas Pages: 16

Brand: Lattice Semiconductor Pages: 26

Brand: Datavideo Pages: 17

Brand: Datamax Pages: 22

Brand: Omnex Pages: 9

Brand: Omegon Pages: 6

Brand: WATERLOO Pages: 8

Brand: WAREMA Pages: 4

Brand: Apricus Pages: 32

Linear Technology ADI Power DC3017A

Brand: Analog Devices Pages: 12

Brand: Frico Pages: 8

MultiConnect Dragonfly MTQ-MNA1-B01

Brand: Multitech Pages: 45

Sundstrom SR307

Brand: S.E.A. Group Pages: 5

Brand: Partlow Pages: 49

Brand: Ascon tecnologic Pages: 11

Brand: ROBOT3T Pages: 21

Brand: StudioComm Pages: 61

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands