manualshive.com logo in svg

Infineon Technologies XC2200, User Manual

Share
Download
Infineon Technologies XC2200 User Manual Download Page 309

XC2200 Derivatives

System Units (Vol. 1 of 2)

System Control Unit (SCU)

 

User’s Manual

6-49

V2.1, 2008-08

SCU, V1.13

 

6.3

Reset Operation

All resets are generated by the Reset Control Block. It handles the control of the reset
triggers as well as the length of a reset and the reset timing. A reset leads the system,
or a part of the system depending on the reset, to a initialization into a defined state.

6.3.1

Reset Architecture

The XC2200 contains a very sophisticated reset architecture to offer the greatest amount
of flexibility for the support of different applications. The reset architecture supports the
different power domains. 
If a power domain is deactivated all resets of the deactivated level and all resets of all
lower power domains are asserted.
Different reset types for the complete system are supported.

6.3.1.1

Device Reset Hierarchy

The device reset hierarchy is divided according to the power domains (see 

Chapter 6.5

)

into following linked levels:
Level 1: I/O domain (power domain DMP_B)
Level 2: Wake-up domain (power domain DMP_M)
Level 3: System domain (power domain DMP_1)
If a power domain (level) is deactivated all resets of the deactivated level and all resets
of all lower power domains are asserted. 

6.3.1.2

Reset Types

The following summary shows the different reset types.

Power Reset

•

Power-on Reset
This reset leads to a defined state of the complete system. This reset should only be
requested on a real power-on event and not by any non power related event.

•

Power Reset for DMP_M and DMP_1 power domains
This reset regains data consistency upon a power fail in the DMP_M or DMP_1
power domains.

•

Power Reset DMP_1 power domain
This reset prevents data inconsistency upon entry into and exit from power saving
modes, where DMP_1 is switched off.

Summary of Contents for XC2200






































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands