manualshive.com logo in svg

Infineon Technologies XC2200, User Manual

Share
Download
Infineon Technologies XC2200 User Manual Download Page 308

XC2200 Derivatives

System Units (Vol. 1 of 2)

System Control Unit (SCU)

 

User’s Manual

6-48

V2.1, 2008-08

SCU, V1.13

 

Note: The bits in the upper byte of register WUCR indicate the current status of the

wake-up counter logic. They are not influenced by a write access, but are
controlled by their associated control fields (lower byte) or by hardware.
The control bit(field)s in the lower byte of register WUCR determine the state of
the status bits (upper byte) of the wake-up counter logic. Setting bits by software
triggers the associated action, writing 0 has no effect.

AON

9

rh

Auto-Start Indicator

0

B

Wake-up counter is started by software only

1

B

Wake-up counter can be started by the PSC 
mechanism

ASP

10

rh

Auto-Stop Indicator

0

B

Wake-up counter runs continuously

1

B

Wake-up counter stops after generating a 
trigger when reaching zero

TTSTAT

14

rh

Trim Trigger Status

0

B

No trim trigger event is active. No trim interrupt 
trigger is generated.

1

B

A trim trigger event is active. A trim interrupt 
trigger is generated.

Note: This bit is not valid if f

SYS

= f

WU

 is configured by

SYSCON0.CLKSEL

WUTRG

15

rh

WUT Trigger Indicator

0

B

No trigger event has occurred since WUTRG 
has been cleared last. No interrupt trigger is 
generated.

1

B

A wake-up trigger event has occurred. A wake-
up interrupt trigger is generated.

0

6, 
[13:11]

r

Reserved

Read as 0; should be written with 0.

Field

Bits

Type

Description

Summary of Contents for XC2200






































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands