manualshive.com logo in svg

Infineon Technologies XC2200, User Manual

Share
Download
Infineon Technologies XC2200 User Manual Download Page 243

XC2200 Derivatives

System Units (Vol. 1 of 2)

Interrupt and Trap Functions

 

User’s Manual

5-31

V2.1, 2008-08

ICU_X2K, V2.2

 

5.5

Prioritization of Interrupt and PEC Service Requests

Interrupt and PEC service requests from all sources can be enabled so they are
arbitrated and serviced (if they win), or they may be disabled, so their requests are
disregarded and not serviced.

Enabling and disabling interrupt requests

 may be done via three mechanisms: 

•

Control Bits

•

Priority Level

•

ATOMIC and EXTended Instructions

Control Bits

 allow switching of each individual source “ON” or “OFF” so that it may

generate a request or not. The control bits (xxIE) are located in the respective interrupt
control registers. All interrupt requests may be enabled or disabled generally via bit IEN
in register PSW. This control bit is the “main switch” which selects if requests from any
source are accepted or not.
For a specific request to be arbitrated, the respective source’s enable bit and the global
enable bit must both be set.

The Priority Level

 automatically selects a certain group of interrupt requests to be

acknowledged and ignores all other requests. The priority level of the source that won
the arbitration is compared against the CPU’s current level and the source is serviced
only if its level is higher than the current CPU level. Changing the CPU level to a specific
value via software blocks all requests on the same or a lower level. An interrupt source
assigned to level 0 will be disabled and will never be serviced.

The ATOMIC and EXTend instructions

 automatically disable all interrupt requests for

the duration of the following 1 … 4 instructions. This is useful for semaphore handling,
for example, and does not require to re-enable the interrupt system after the inseparable
instruction sequence.

Interrupt Class Management

An interrupt class covers a set of interrupt sources with the same importance, i.e. the
same priority from the system’s viewpoint. Interrupts of the same class must not interrupt
each other. The XC2200 supports this function with two features:
•

Classes with up to eight members

 can be established by using the same interrupt

priority (ILVL) and assigning a dedicated group level to each member. This
functionality is built-in and handled automatically by the interrupt controller.

•

Classes with more than eight members

 can be established by using a number of

adjacent interrupt priorities (ILVL) and the respective group levels (eight per ILVL).
Each interrupt service routine within this class sets the CPU level to the highest
interrupt priority within the class. All requests from the same or any lower level are
blocked now, i.e. no request of this class will be accepted.

Summary of Contents for XC2200






































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands