Hinowa LightLift 15.70 3S Technical Course Booklet Download Page 2

Page: 2 / 137

INDEX

............................................................................................................................. 6

1.1

PARTS DENOMINATION

.............................................................................................................. 6

1.2

SERIAL NUMBER LOCATION

..................................................................................................... 8

LL15.70 DATA

................................................................................................................................. 9

2.2

TECHINCAL SPECIFICATIONS

.................................................................................................. 9

2.3

LL15.70 DIMENSIONS

............................................................................................................... 11

2.4

LL15.70 WORKING AREA - 230 KG UNRESTRICTED CAPACITY

............................... 13

MACHINE OPERATIONAL INTRODUCTION

........................................................................ 14

3.1

MACHINE IGNITION

................................................................................................................... 14

3.2

STOP BUTTONS

............................................................................................................................ 16

3.3

REMOTE CONTROL FUNCTIONS

............................................................................................ 16

GROUND PART MOVEMENTS

.................................................................................................. 18

4.1

TRACKS MOVEMENTS

................................................................................................................ 18

4.1.1

TRACKS WIDENING

........................................................................................................... 21

4.1.2

TRACKS MOVEMENT SPEED SELECTION

................................................................... 21

4.1.3

TRACKS AUTOMATIC SPEED CONTROL

..................................................................... 22

4.2

OUTRIGGERS MOVEMENTS

..................................................................................................... 23

4.2.1

AUTOMATIC STABILIZATION

......................................................................................... 24

4.2.2

OUTRIGGERS AUTO-RETRACTION

............................................................................... 25

4.2.3

SINGLE OUTRIGGER MOVEMENTS

............................................................................... 27

AERIAL PART MOVEMENTS

..................................................................................................... 28

5.1

ENGINE CARTER CONTACT PREVENTION SYSTEM

........................................................ 30

PEDAL (OPTIONAL)

.................................................................................................................... 31

EMERGENCY OPERATIONS

...................................................................................................... 32

7.1

EMERGENCY DEVICES AND TOOLS LOCATION

............................................................... 32

7.2

AERIAL PART EMERGENCY OPERATIONS

.......................................................................... 34

7.2.1

GRAVITY EMERGENCY DESCENT

...................................................................................... 35

7.2.2

OPERATIONS FROM GROUND CONTROL POSITION

.................................................. 36

7.2.3

EMERGENCY DESCENT WITH SAFETIES BY-PASS

..................................................... 37

7.2.4

EMERGENCY DESCENT FROM THE GROUND WITH HAND PUMP

.......................... 38

7.3

GROUND PART EMERGENCY MOVEMENTS

........................................................................ 40

7.3.1

TRACKS MOVEMENT WITH SAFETIES BY-PASS

.......................................................... 40

7.3.2

OUTRIGGERS MOVEMENT WITH THE HAND PUMP

.................................................... 41

Summary of Contents for LightLift 15.70 3S










































































































































Search results

Summary of Contents for LightLift 15.70 3S

Reviews:

Related manuals for LightLift 15.70 3S

Brands by name

Popular brands

Hinowa LightLift 15.70 3S, Technical Course Booklet

Search results

Summary of Contents for LightLift 15.70 3S

Reviews:

Related manuals for LightLift 15.70 3S

Brands by name

Popular brands