Hinowa LightLift 15.70 3S Technical Course Booklet Download Page 105 | Manualshive

Page: 105 / 137

background image

105

NOTE: The set-point rpm could be different from the nominal rpm configuration

depending on the electric load.

RPM SETTING

ECM1 through its internal contacts communicates the required rpm selection to
the inverter, which will feed the electric motor with the relevant frequency in

order to achieve the nominal rpm selected, the actual rpm depends also on the
machine working conditions.

Here below is listed the rpm setting according to the movement required and

to the speed selected.

MOVEMENT

TURTLE

NORMAL

HARE

TRACKS

1500

2100

2100 +

SECOND SPEED

TRACKS WIDENING

1500

2100

2100

1-2 BOOMS DOWN

750

1500 +

DOUBLE PUMP

1500 +

DOUBLE PUMP

1-2 BOOMS DOWN

750

1500

1500

3 BOOM UP

750

1800

1800

3 BOOM DOWN

750

1500

1500

1-2 AND 3 BOOMS TOGETHER WITH

AT LEAST ONE UP

1500

1800

1800

1-2 AND 3 BOOMS TOGETHER,

NONE UP

1050

1500

1500

TELESCOPE OUT

1500

1800 +

DOUBLE PUMP

1800 +

DOUBLE PUMP

TELESCOPE IN

1500

1800

1800

SLEW ROTATION

750

1500

1500

JIB

750

1050

1050

BASKET ROTATION

750

1050

1050

BASKET LEVELLING

750

1050

1050

NOTE: Outriggers rpm depends on the machine condition.

NOTE: Tracks opposite rotation is carry out with lower speed.

NOTE: Aerial contemporary movements including jib, basket leveling or
rotation are carry ion at minimum rpm.

NOTE: Double pump valve is not activated with movements together.

«
...
103
104
105
106
107
...
»

Summary of Contents for LightLift 15.70 3S










































































































































Reviews:

No comments

Related manuals for LightLift 15.70 3S

Brand: Keithley Pages: 97

Brand: Happ Pages: 52

Brand: Harman Pages: 20

OBID ID ISC.ANT40/30

Brand: Feig Electronic Pages: 2

Brand: OMG Pages: 32

Pulse-Expert M-400S

Brand: Masterweld Pages: 25

Brand: Falco Pages: 65

Brand: Raider Pages: 74

Brand: P.I.T. Pages: 34

Brand: Telpro Pages: 6

Brand: Ravaglioli Pages: 104

Brand: Walter Pages: 30

Brand: IDENTEC SOLUTIONS Pages: 26

Brand: WARPP Pages: 14

Brand: Salda Pages: 28

Brand: Rotary Pages: 12

Brand: Rehasense Pages: 6

CADB/T-HE PRO-REG Series

Brand: S&P Pages: 72

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands