Hinowa LightLift 15.70 3S Technical Course Booklet Download

Page: 39 / 137

Press the proportional valve red lever keeping it completely pressed while
acting on the required movement lever as indicated at point d)

While pumping with hand pump and while proportional valve lever is

completely pressed, act on the movements levers following the sticker
indications on the rear side of the cover.

Emergency lowering must be done following the safer movements sequence.

NOTE: In case the ground control box is closed, open it with the proper key

NOTE: Operating with hand pump of course there’s no electronic control

activated including the engine carter contact prevention system.

MOVEMENTS

LEVERS

PROPORTIONAL

VALVE WITH RED

LEVER

Summary of Contents for LightLift 15.70 3S










































































































































Search results

Summary of Contents for LightLift 15.70 3S

Reviews:

Related manuals for LightLift 15.70 3S

Brands by name

Popular brands

Hinowa LightLift 15.70 3S, Technical Course Booklet

Search results

Summary of Contents for LightLift 15.70 3S

Reviews:

Related manuals for LightLift 15.70 3S

Brands by name

Popular brands