Hinowa LightLift 15.70 3S Technical Course Booklet Download Page 115

Page: 115 / 137

115

CONNECTOR ON

REMOTE

CONTROL THE

GROUND CABLE

Here follows the calibration procedure:

CONNECT THE REMOTE CONTROL AT ITS

GROUND CABLE AND SELECT THE CONTROL
POSITION ACCORDINGLY BY THE CONTROL

POSITION SELECTOR SWITCH

Turn ON the main key and select the correct machine model with button n.1

(VERSION), the display shows the machine model selected.

If it appears “MOD.CODE FAIL!”, it means

that the machine model selected

is not correct, even if that alarm does not appear on the display the machine
model selected need to be check.

Here below the example shows on the image A the case of machine model
selected is wrong, and on image B the case of machine model selected is

the right one (for a LL15.70)

In case of the engine model selected is not correct with button n.7 (MOTOR)

select the correct one (for instance “D.RPM” is the diesel Hatz 1B40 and

“G.13L” is the gasoline

Honda iGX390)

MACHINE MODEL

SELECTED IS OK

MACHINE MODEL

SELECTED IS WRONG

Summary of Contents for LightLift 15.70 3S










































































































































Search results

Summary of Contents for LightLift 15.70 3S

Reviews:

Related manuals for LightLift 15.70 3S

Brands by name

Popular brands

Hinowa LightLift 15.70 3S, Technical Course Booklet

Search results

Summary of Contents for LightLift 15.70 3S

Reviews:

Related manuals for LightLift 15.70 3S

Brands by name

Popular brands