Hinowa LightLift 15.70 3S Technical Course Booklet Download Page 14

Page: 14 / 137

MACHINE OPERATIONAL INTRODUCTION

The LL15.70 aerial platform is divided into two main parts:



Ground part (or undercarriage part)



Aerial part

Driving or using the outriggers we are using the ground part.
Moving the booms or the turret rotation we are using the aerial part.

All of those movements are carried out by the remote control.

3.1

MACHINE IGNITION

To start up the machine the battery cutter must be active, when main key on

ground control box is turned ON display will show the following icon indicating
to press and release the remote control emergency stop button to initialize the

machine.

After stop button will be pressed and released the machine is ready to be used
and main display indications will be visualized.

IN cas e of nec

To switch ON the electric motor the machine need to be plugged to the local
electric network with a proper cable, shorter than 10m and with a minimum

section of 2,5mm2 (220V network) or 4mm2 (110V network).
To ignite engine or electric motor, both the emergency stop buttons, on the

remote control and on the ground control box, must be released.

MAIN KEY

TURNED

“ON”

BATTERY

CUTTER

INITIALIZATION

ICON

PRESS AND

RELEASE

THE STOP

BUTTON

Summary of Contents for LightLift 15.70 3S










































































































































Search results

Summary of Contents for LightLift 15.70 3S

Reviews:

Related manuals for LightLift 15.70 3S

Brands by name

Popular brands

Hinowa LightLift 15.70 3S, Technical Course Booklet

Search results

Summary of Contents for LightLift 15.70 3S

Reviews:

Related manuals for LightLift 15.70 3S

Brands by name

Popular brands