Hinowa LightLift 15.70 3S Technical Course Booklet Download Page 38

Page: 38 / 137

7.2.4

EMERGENCY DESCENT FROM THE GROUND WITH HAND PUMP

EMERGENCY POTENTIAL SITUATIONS:



Engine and/or electric motor not working



Electrical system out of order

The only purpose of the emergency descent from the ground with hand pump
is a machine breakdown. Any other use is forbidden.

To carry out the movement required hydraulic oil has to be manually pumped

while using the ground controls.
Hand pump is not designed for lifting booms, i

t’s forbidden to carry out different

operations than the ones specified by the present procedure, in particular are
forbidden operations such as telescope opening, booms lifting, outriggers

movements while machine is not closed and aligned or with person in the
basket, in general any operation that may compromise the machine stability.

To carry out emergency descent from the ground with hand pump the here

below steps have to strictly followed.

a)

Turn OFF the main key

Shift the deviator on the manual pump into the position for aerial part

movement (rightward) as indicated by the hand pump sticker and place
the hand pump lever, that is under the aerial part valveblock carter.

HAND PUMP

DEVIATOR

HAND PUMP

LEVER

Summary of Contents for LightLift 15.70 3S










































































































































Search results

Summary of Contents for LightLift 15.70 3S

Reviews:

Related manuals for LightLift 15.70 3S

Brands by name

Popular brands

Hinowa LightLift 15.70 3S, Technical Course Booklet

Search results

Summary of Contents for LightLift 15.70 3S

Reviews:

Related manuals for LightLift 15.70 3S

Brands by name

Popular brands