Hinowa LightLift 15.70 3S Technical Course Booklet Download Page 75

Page: 75 / 137

9.9

12 VOLT BATTERY

The machine electric system works at 12 Volt, the accumulation system is

composed by an AGM start&stop battery with a capacity of 60 Ah.

12 Volt battery is feed by the engine generator while engine is running or by
the transformer described by the following chapter while machine is plugged to

the electric network.

9.10

BATTERY CHARGE SYSTEM

The battery charge is carried out by the electronic transformer located under
the base bonnet aside the electric motor.

The output tension from the electronic transformer is fixed at 13,4 Volt DC and
it does not depend on the electric network tension or frequency.

The output current is regulated at about 15 Amp.

Summary of Contents for LightLift 15.70 3S










































































































































Search results

Summary of Contents for LightLift 15.70 3S

Reviews:

Related manuals for LightLift 15.70 3S

Brands by name

Popular brands

Hinowa LightLift 15.70 3S, Technical Course Booklet

Search results

Summary of Contents for LightLift 15.70 3S

Reviews:

Related manuals for LightLift 15.70 3S

Brands by name

Popular brands