Hinowa LightLift 15.70 3S Technical Course Booklet Download

Page: 136 / 137

136

MICROJIB A

The JIB is closed

–

the control switch is released and “A” line is closed

OFF

The JIB is open

–

the control switch is pressed and “A” line is open

MICROJIB B

The JIB is closed

–

the control switch is

released and “B” line is open

OFF

The JIB is open

–

the control swi

tch is pressed and “B” line is closed

PEDAL A

The pedal is pressed

–

the pedal electric line "A" is closed

Option

OFF

The pedal is released

–

the pedal electric line "A" is open

PEDAL B

The pedal is pressed

–

the pedal electric line "B" is open

Option

OFF

The pedal is released

–

the pedal electric line "B" is closed

R.C. BASKET

The remote control is in the support in basket

OFF

The remote control is not in the support in basket

TRACK OPEN A

Tracks are fully widened. Widening cylinders switches "A" are pressed,
contact is closed

OFF

Tracks are not fully widened. Widening cylinders switches "A" are
released, contact is open

TRACK OPEN B

Tracks are fully widened. Widening cylinders switches "B" are pressed,
contact is closed

OFF

Tracks are not fully widened. Widening cylinders switches "B" are
released, contact is open

Summary of Contents for LightLift 15.70 3S










































































































































Search results

Summary of Contents for LightLift 15.70 3S

Reviews:

Related manuals for LightLift 15.70 3S

Brands by name

Popular brands

Hinowa LightLift 15.70 3S, Technical Course Booklet

Search results

Summary of Contents for LightLift 15.70 3S

Reviews:

Related manuals for LightLift 15.70 3S

Brands by name

Popular brands