Hinowa LightLift 15.70 3S Technical Course Booklet Download Page 96

Page: 96 / 137

Fit the remote control on the ground cable

Before than switch ON the machine, in
order to select the remote control ground

position, turn left the control position
selector switch, as indicated by the sticker

Turn ON main key and check remote

control display to be sure procedure was
properly fulfilled, than machine will be
ready to be used. From this position at the

ground it’s possible to move both

the aerial

part and the ground part.

While using aerial part with remote control

connected on the ground the control module will

avoid moving if there’s more than 50 Kg in the

basket.

Only for emergency reasons it’s possible,

pressing and keeping pressed remote control
button n.8, to enable the aerial part movement

even with more than 50 Kg.

CONTROL POSITION

SELECTOR SWITCH

Summary of Contents for LightLift 15.70 3S










































































































































Search results

Summary of Contents for LightLift 15.70 3S

Reviews:

Related manuals for LightLift 15.70 3S

Brands by name

Popular brands

Hinowa LightLift 15.70 3S, Technical Course Booklet

Search results

Summary of Contents for LightLift 15.70 3S

Reviews:

Related manuals for LightLift 15.70 3S

Brands by name

Popular brands