Hinowa LightLift 15.70 3S Technical Course Booklet Download Page 29

Page: 29 / 137

It’s possible to move more than one joystick at the same time, however the

possibility to carry out two or more aerial part movements at the same time
depends on several factors such as the position of the booms.

In case of a joystick has been used while machine doesn’t satisfy all the

stabilization conditions, display will show a stabilization error message that

indicate with “NO” which condition/conditions i

s/are not satisfied, as in the

examples here below.



ST”X” FAIL indicates that outrigger n.X is not touching

the ground



INCL FAIL means that the machine is not levelled

within the inclination clearance



LOAD FAIL means that basket is overloaded (more
than 230Kg into the basket so more than about 280

Kg charged on the load sensor). In this case of the
basket is overloaded display will visualize also the

“OVERLOAD” icon.



BASKET FAIL means that the remote control is not

properly placed on its basket support



PEDAL (OPTIONAL) FAIL means that pedal option is
activated and pedal was not properly pressed in order

to allowed the movement



AUTOST: Auto-stabilization procedure not completed
properly

BLACK JOYSTICKS FOR AERIAL PART

MOVEMENTS WITH RELEVANT DECALS

KEY SWITCH FOR

THE ADJUSTMENT

OF BASKET

LEVELLING

ST1 FAIL

INCL FAIL

BASKET FAIL

Summary of Contents for LightLift 15.70 3S










































































































































Search results

Summary of Contents for LightLift 15.70 3S

Reviews:

Related manuals for LightLift 15.70 3S

Brands by name

Popular brands

Hinowa LightLift 15.70 3S, Technical Course Booklet

Search results

Summary of Contents for LightLift 15.70 3S

Reviews:

Related manuals for LightLift 15.70 3S

Brands by name

Popular brands