Hinowa LightLift 15.70 3S Technical Course Booklet Download Page 83

Page: 83 / 137

PROXIMITY

Turret is not almost completely rotated, contact is close, 1st-2nd
booms are not above the engine

OFF

Turret is almost completely rotated, contact is open, 1st-2nd booms
are above the engine

MICR. BR. 1-2

Indicates that 1st boom is not opened enough to rotate above the
engine carter

OFF

Indicates that 1st boom is opened enough to rotate above the engine
carter

SKYGUARD

Indicates that Skyguard bar has been pressed.

OFF

Indicates that Skyguard bar has not been pressed.

MOTOR RPM

(Only for

Diesel

machine)

2220

Indicates the Diesel engine rpm

TEMPERAT.

37,62

Indicates the temperature of the ECM1 in °C

SUPPLY (V)

12,15

Indicates the batteries voltage, or the output voltage from the battery
charger

ONLY LITHIUM INPUT

SOC

Indicates the charge level of the battery pack, 100 % is the
maximum, 0 % is the minimum

V LITHIUM

Indicates the total voltage of the lithium pack. When the cells are not
under charge or under discharge, it tends to the nominal value that is

around 40 Volt, it doesn’t ma

tter

their charge status.

A BATTERY

Indicates the value of the current (Amp) measured by the LEM sensor.
With

sign “–“

the current is going out from the battery pack (discharge), if

there is
no sign, the current is going inside the pack (charge)

Summary of Contents for LightLift 15.70 3S










































































































































Search results

Summary of Contents for LightLift 15.70 3S

Reviews:

Related manuals for LightLift 15.70 3S

Brands by name

Popular brands

Hinowa LightLift 15.70 3S, Technical Course Booklet

Search results

Summary of Contents for LightLift 15.70 3S

Reviews:

Related manuals for LightLift 15.70 3S

Brands by name

Popular brands