Hinowa LightLift 15.70 3S Technical Course Booklet Download Page 34

Page: 34 / 137

Machine is equipped with the following keys and tool necessary to fulfil some
emergency operation.



Main key (same of by-pass key)

–

PART CODE 1651290015



Ground control box key

–

PART CODE 07298800



Basket levelling spare key

–

PART CODE WITH CAP 2683930002

NOTE: After an emergency procedure, all the emergency devices and tool

must be put back on original position/condition.

7.2

AERIAL PART EMERGENCY OPERATIONS

The main purpose of an emergency descent is to safely take to the ground the

operator staying into the basket.
Some emergency descent can be carried out from the basket, some other from
the ground.

MAIN KEY AND

BY-PASS KEY

GROUND

CONTROL

BOX KEY

BASKET

LEVELING

SPARE KEY

N.2 X MAIN KEY

N.2 X GROUND CONTROL BOX KEY

N.1 X BASKET LEVELING SPARE KEY

N.2 X MAIN KEY

Summary of Contents for LightLift 15.70 3S










































































































































Search results

Summary of Contents for LightLift 15.70 3S

Reviews:

Related manuals for LightLift 15.70 3S

Brands by name

Popular brands

Hinowa LightLift 15.70 3S, Technical Course Booklet

Search results

Summary of Contents for LightLift 15.70 3S

Reviews:

Related manuals for LightLift 15.70 3S

Brands by name

Popular brands