Hinowa LightLift 15.70 3S Technical Course Booklet Download Page 26

Page: 26 / 137

While

“AUTOMATIC OUTRIGGERS RETRACTION”

button is pressed the display

shows the outriggers conditions, as indicated by the example here below.

Keeping

“AUTOMATIC OUTRIGGERS RETRACTION”

button pressed till

outriggers are completely lifted up machine will reach the stowed condition.

Machine is equipped with two pressure switches on the hydraulic manifold, one
for the right side and one for the left side. When both the same side outriggers

cylinders are at end of their stroke, that side hydraulic oil pressure rises to the
maximum value and it is detected by the pressure switch.

When both sides oil pressures are at maximum values machine starts to feed
only one side outriggers at a time, in order to have more power available.

This helps when, especially with electric motor, outriggers need more power to
be moved, as when hydraulic oil is very cold.

“

OUTRIGGERS AUTOMATIC

RETRACTION

”

BUTTON

AUTODESTAB

WAIT

ST1 GND

ST2 NO GND
ST3 NO GND

ST4 NO GND

AUTS

STEP: 105
SOLL

STEP: 0

AUTODESTAB

WAIT

ST1 GND
ST2 GND

ST3 GND
ST4 GND

AUTS
STEP: 1

SOLL
STEP: 0

AUTODESTAB

WAIT

ST1 NO GND
ST2 NO GND

ST3 NO GND

ST4 NO GND

AUTS
STEP: 0

SOLL

STEP: 1

PRESSURE

SWITCHES

Summary of Contents for LightLift 15.70 3S










































































































































Search results

Summary of Contents for LightLift 15.70 3S

Reviews:

Related manuals for LightLift 15.70 3S

Brands by name

Popular brands

Hinowa LightLift 15.70 3S, Technical Course Booklet

Search results

Summary of Contents for LightLift 15.70 3S

Reviews:

Related manuals for LightLift 15.70 3S

Brands by name

Popular brands