Hinowa LightLift 15.70 3S Technical Course Booklet Download Page 43

Page: 43 / 137

Press the right proportional valve button keeping it completely pressed
while acting on the required outrigger lever as indicated at point f)

While pumping with hand pump and while proportional valve button is

completely pressed, act on the right side relevant levers, as indicated by
the sticker, to move the outriggers (n.3 and n.4)

In order to move the left side outriggers, shift the deviator on the manual

pump into the position for ground left side (leftward) as indicated by the
hand pump sticker and place the hand pump lever

HAND PUMP

DEVIATOR

HAND PUMP

LEVER

RIGHT SIDE GROUND

PROPORTIONAL VALVE BUTTON

AND OUTRIGGERS LEVERS

Summary of Contents for LightLift 15.70 3S










































































































































Search results

Summary of Contents for LightLift 15.70 3S

Reviews:

Related manuals for LightLift 15.70 3S

Brands by name

Popular brands

Hinowa LightLift 15.70 3S, Technical Course Booklet

Search results

Summary of Contents for LightLift 15.70 3S

Reviews:

Related manuals for LightLift 15.70 3S

Brands by name

Popular brands