Hinowa LightLift 15.70 3S Technical Course Booklet Download Page 121

Page: 121 / 137

121

Here follows the list of the main DEVICEs that could affected by that kind of
anomalies, not all the DEVICEs are listed.

TABLE 1 - DEVICES

DEVICE CODE

DEVICE DESCRIPTION

Ground part right side proportional valve coil

Ground part left side proportional valve coil

Right track forward valve coil

Left track forward valve coil

Right track backward valve coil

Left track backward valve coil

Outrigger n.1 lowering valve coil

Outrigger n.2 lowering valve coil

Outrigger n.3 lowering valve coil

Outrigger n.4 lowering valve coil

Outrigger n.1 lifting valve coil

Outrigger n.2 lifting valve coil

Outrigger n.3 lifting valve coil

Outrigger n.4 lifting valve coil

1-2 booms lifting valve coil

3 boom lifting valve coil

1-2 booms lowering valve coil

3 boom lowering valve coil

Telescope extraction valve coil

Telescope retraction valve coil

Jib opening valve coil

Jib closing valve coil

Basket levelling up valve coil

Basket levelling down valve coil

Turntable right rotation valve coil

Turntable left rotation valve coil

Basket right rotation valve coil

Basket left rotation valve coil

Aerial part proportional valve coil

Pumps sum valve coil

Tracks second speed valve coil

Tracks widening valve coil

Tracks closing valve coil

1-2 booms gravity descent valve coil

3 boom gravity descent valve coil

Deviator (aerial part/ground part) valve coil

NOTE: On LL13.70 the DEVICES 48 and 49 are marked with error 7 because
the basket rotation is not available. On LL13.70 with fix undercarriage (without

tracks widening system), the DEVICES 53 and 54 are marked with error 2
because the track widening is not available.

Summary of Contents for LightLift 15.70 3S










































































































































Search results

Summary of Contents for LightLift 15.70 3S

Reviews:

Related manuals for LightLift 15.70 3S

Brands by name

Popular brands

Hinowa LightLift 15.70 3S, Technical Course Booklet

Search results

Summary of Contents for LightLift 15.70 3S

Reviews:

Related manuals for LightLift 15.70 3S

Brands by name

Popular brands