Hinowa LightLift 15.70 3S Technical Course Booklet Download Page 37 | Manualshive

Page: 37 / 137

background image

37

7.2.3

EMERGENCY DESCENT WITH SAFETIES BY-PASS

In case of neither gravity emergency descent nor operations from ground

control position are possible, it’s possible to carry out the emergency descent

with safeties by-pass.

WARNING:

-

The safety devices by-pass is an extremely dangerous operation and

must be carried out only by qualified personnel and only in emergency
situations.

-

The control module records date, time and all the operations carried out

during the by-pass, Hinowa personnel could analyse those data.

-

Normal conditions have to be restored as soon as emergency has been
overcome.

EMERGENCY POTENTIAL SITUATIONS:

-

Machine has lost one of the stabilization conditions

-

Gravity emergency descent is not possible (ex. booms above an obstacle)

-

It’s required to rotate the turret to align the machine after the gravity

emergency descent

CONDITIONS REQUIRED:



Engine and/or electric motor properly working



Electrical system properly functioning

The aerial part safety device by-pass can be carried out by using the safeties
by-pass key switch that is under the slot on the left side of the electric

components compartment, installed on the machine rear side of the machine.
Keeping turned the safeties by-pass key switch leftwards (see the decal) the

aerial part safety devices are by-passed. The safeties by-pass key must be kept
turned while moving the machine. As soon as the safeties are by-passed the

display will show the AERIAL PART SAFETIES BY-PASS icon for a few seconds,
then the same icon will appear in position n.7.

NOTE:

In order to fulfil this emergency operation, it’s required the by

-pass key.

NOTE: Safeties by-pass procedure does not by-pass engine carter contact
prevention system.

«
...
35
36
37
38
39
...
»

Summary of Contents for LightLift 15.70 3S










































































































































Reviews:

No comments

Related manuals for LightLift 15.70 3S

Brand: Geberit Pages: 49

IntelliZone2 MasterStat

Brand: Water Furnace Pages: 44

Brand: Balboa Pages: 23

Brand: M-system Pages: 7

Brand: ENTRYPASS Pages: 42

Genie GS-2669 DC

Brand: Terex Pages: 147

Brand: Ravaglioli Pages: 104

Hammerfall DIGI9652

Brand: RME Audio Pages: 22

Brand: Zepro Pages: 68

Brand: FAAC Pages: 16

Brand: Lincoln Electric Pages: 36

Brand: Aircalo Pages: 28

Brand: Sunrise Medical Pages: 36

Brand: Vasco Pages: 32

Brand: salmson Pages: 40

CITOTIG 250 AC/DC

Brand: Oerlikon Pages: 136

Brand: Jazz Pages: 12

Brand: AWELCO Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands