Hinowa LightLift 15.70 3S Technical Course Booklet Download Page 23

Page: 23 / 137

SPEED CONTROL CONDITIONS ON Y AXLE

JIB OPEN



HARE NOT

AVAILABLE

Y>6°

TURTLE

Y>10°

BEEPER

Y>16°

STOP

+ ALARM ICON

JIB CLOSED

WEIGHT

≤ 120Kg

Y>6°

TURTLE

Y>9°

BEEPER

Y>13°

STOP

+ ALARM ICON

JIB CLOSED

WEIGHT

≤ 230Kg



HARE NOT

AVAILABLE

Y>6°

TURTLE

Y>8°

BEEPER

Y>10°

STOP

+ ALARM ICON

4.2

OUTRIGGERS MOVEMENTS

To be able to use the aerial part movements
outriggers must be settled, this chapter
details how to do it.

To allow outriggers movements machine must
be closed and aligned, this condition is
indicated by the relevant icon displayed on
position n.6.

Machine is closed and aligned when booms
(including jib) are completely lowered

(cylinder closed) and turret is aligned as
indicated by the two arrows (see picture

aside) that the operator has to keep as visual
reference.

Closed and aligned condition is verified by the
two photocells that have to receive the signal

reflected by the reflector installed on the jib
arm bottom part as indicated in picture here
below.

Summary of Contents for LightLift 15.70 3S










































































































































Search results

Summary of Contents for LightLift 15.70 3S

Reviews:

Related manuals for LightLift 15.70 3S

Brands by name

Popular brands

Hinowa LightLift 15.70 3S, Technical Course Booklet

Search results

Summary of Contents for LightLift 15.70 3S

Reviews:

Related manuals for LightLift 15.70 3S

Brands by name

Popular brands