8
8
8-109
8-109
Service Mode > COPIER > OPTION > FNC-SW
Service Mode > COPIER > OPTION > FNC-SW
COPIER > OPTION > FNC-SW
CARD-RNG
Card number setting (department number)
Lv.2 Details
To set the number of cards (departments) that can be used with the
Card Reader.
Use case
When setting the number of cards (departments)
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range
1 to 1000
Default value
1000
ARCDT-SW
ON/OFF of ARCDAT control
Lv.1 Details
To set ON/OFF of ARCDAT control.
When 1 is set, the ARCDAT control is not executed.
When the hue variation occurs in the case of failure value displayed in
COPIER> DISPLAY> HT-C, turn OFF the ARCDAT control once and
check the hue.
If hue variation is alleviated, analyze the cause of ARCDAT control
error (developer, Patch Sensor, etc.).
When 1 (ARCDAT control is OFF.) is set, DH-SW becomes 0 (D-half
control is OFF.).
Use case
When hue variation occurs
Adj/set/operate method Enter the setting value, and then press OK key.
Caution
Make sure to set 0 again when ARCDAT control recovers. If inputting
a job during D-half control at last rotation while the setting is 1, “Waiting
to print...” might be displayed.
Display/adj/set range
0 to 1
0: ON, 1: OFF
Default value
0
Related service mode COPIER> DISPLAY> HT-C
COPIER> OPTION> FNC-SW> DH-SW
SJOB-CL
Set of scan job canceling by logout
Lv.1 Details
To set whether to cancel the scan job in operation by logout of the
user.
Use case
Upon user’s request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution
The job in scanning operation cannot be canceled.
Display/adj/set range
0 to 1
0: Disabled, 1: Enabled
Default value
0
Supplement/memo
Scan job: A job after the scanning operation is completed.
COPIER > OPTION > FNC-SW
USB-RCNT
Auto connect set at USB device disconnct
Lv.2 Details
To set to enable/disable automatic connection when the USB device is
disconnected.
With the setting to disable automatic connection, USB device cannot
be used if disconnecting and then connecting the USB device. To
enable connection again, the power needs to be turned OFF/ON.
With the setting to enable automatic connection, connect again after
disconnecting, and then connecting the USB device again.
Use case
Upon user’s request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution
With the setting to enable automatic connection, disconnecting of 1
area makes automatic connection of all USB devices if there is USB
hub.
Display/adj/set range
0 to 1
0: No automatic connection, 1: Automatic connection
Default value
0
UNLMTBND
Over 400 binders print job support set
Lv.1 Details
To set whether to support print job that exceeds 400 binders.
With the setting to support, the machine makes print by sharing
binders according to job attribution.
Select “1: Not supported” if the user does not print job* with large
quantity of binders.
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range
0 to 1
0: Automatic setting (when the print server is not connected: no
support; When the print server is connected: supported)
1: Not supported
Default value
0
Supplement/memo
* : A job that requires finishing (such as stapling) in one job. Does not
apply in the case of executing finishing with multiple sets of output.
MIBCOUNT
Scope range set of Charge Counter MIB
Lv.2 Details
To set the range of counter information that can be obtained as MIB
(Management Information Base).
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range
0 to 2
0: All charge counters are obtained, 1: Only displayed counter* is
obtained, 2: All charge counters are not obtained
* : Counter specified by the following: COPIER > OPTION > USER >
COUNTER 1 to 6
Default value
0
Related service mode COPIER> OPTION> USER> COUNTER1 to 6
